Blog

7 REASONS TO CHOOSE SCULPSURE® OVER COOLSCULPTING®

Non-invasive body shaping procedures have grown drastically in popularity in the last few years.  What is not to love about non-invasive treatments that are easy, fast, affordable, and comfortable and have zero downtime?  Now that you have decided to free your body of excess fat and you have determined that you do not want to undergo an invasive surgical procedure, you still have choices to make!  The real question you have to answer is which non-invasive fat reduction treatment is the best option. Do you want to freeze your fat or melt it?

There is no question that CoolSculpting® has been ruling the non-invasive fat reduction world for the last 2 to 3 years.  It was not difficult to see why CoolSculpting® was so successful compared to the other non-invasive fat reduction treatments offered at that time.  CoolSculpting® was by far the most effective and results oriented non-invasive fat reduction procedure on the market.

However, similar to all industries the technology in the aesthetics industry is constantly advancing and improving at a rapid pace. Unfortunately for CoolSculpting®, the new kid on the block for non-invasive fat reduction, SculpSure®, has far surpassed them in every aspect, rendering CoolSculpting® a dinosaur in the aesthetics industry.

Here are 7 reasons why the superior technology of SculpSure®, at the Philadelphia area’s Chapin Aesthetics, blows CoolSculpting® out of the water in every facet and the ice age of CoolSculpting® has officially ended.

1.)     Ability to Treat Multiple Areas in One Treatment:  SculpSure® can treat multiple areas at the same time (up to 4 areas).  Whereas, CoolSculpting® can only target one area per treatment.

2.)     SculpSure® Cuts Treatment Time in Less than Half: Your SculpSure® treatment only takes 25 minutes per area compared to CoolSculpting®, which takes 1 hour per area.

3.)     No Suction Necessary:  The applicators used in CoolSculpting® require “pinchable” fat that is large enough to be pulled and sucked up into the applicator for treatment.  First, this can be uncomfortable but more importantly if your problem area is not big enough to get pulled in the applicator this area cannot be treated by CoolSculpting®.

 SculpSure® ensures comfort by utilizing flat applicators that do not use a suction method. This also allows SculpSure® to treat areas that CoolSculpting® cannot because it is not necessary to fill up an applicator of fat.  The technology that SculpSure® employs can treat even the smallest amount of stubborn fat.

4.)     Only ONE 25 Minute Treatment Needed: Although, you can repeat SculpSure® treatments on the same area after 6 weeks, SculpSure® has the ability to reach optimal results in just one treatment. It is common for CoolSculpting® patients to require two or more treatments to achieve their desired result.

 5.)     No Pain, Numbing or Bruising: Many CoolSculpting® patients have reported numbness, pain and bruising that can last for weeks post treatment.  Also, research is now revealing that CoolSculpting® can cause more severe complications such as delayed onset pain and nerve damage.  Delayed on set pain typically occurs a few days post treatment and cause neuropathic symptoms such as stabbing, burning, and shooting pain within the treatment areas that is unresponsive to medications.  SculpSure® patients have not reported pain or discomfort following treatment.

 6.)     Advanced Laser Technology vs. Low Tech Freezing: CoolSculpting® uses a process called Cryolipolysis to freeze fat cells.  The treated areas are exposed to extreme cold.  This method can cause long term nerve damage and pain. SculpSure® utilizes laser technology to heat the fat cells to release them from the tissue to be naturally eliminated by the body.  The treatment can be described as a soothing, warming sensation that does not pose any threats to the tissue or nerves.

 7.)     Lower Cost & Increased Efficiency: The fact that SculpSure® can treat 4 areas at one time in 25 minutes and CoolSculpting® can only treat 1 area an 1 hour you saving over 50% of your time.